...インデントエラー：インデントが外側のインデントレベルと一致しません "

Question

ここは私のコードです...私のコードでは何が間違っていますか... ...識別ライン161のエラー... ....ライン161 ....インデントエラー：インデント解除は任意の外側のインデントレベルと一致していない」

ヘルプ ヘルプ ヘルプ

import sys 
import RPi.GPIO as GPIO 
import os 
import Adafruit_DHT 
import urllib2 
import smbus 
import time 
from ctypes import c_short 

#Register Address 
regCall = 0xAA 
regMean = 0xF4 
regMSB = 0xF6 
regLSB = 0xF7 
regPres = 0x34 
regTemp = 0x2e 

DEBUG = 1 
sample = 2 
deviceAdd =0x77 

humi="" 
temp="" 

#bus = smbus.SMBus(0) #for Pi1 uses 0 
I2cbus = smbus.SMBus(1) # for Pi2 uses 1 

DHTpin = 17 

key="30BCDSRQ52AOI3UA"  # Enter your Write API key from ThingSpeak 

GPIO.setmode(GPIO.BCM) 
# Define GPIO to LCD mapping 
LCD_RS = 18 
LCD_EN = 23 
LCD_D4 = 24 
LCD_D5 = 16 
LCD_D6 = 20 
LCD_D7 = 21 

GPIO.setwarnings(False) 
GPIO.setmode(GPIO.BCM)  
GPIO.setup(LCD_E, GPIO.OUT) 
GPIO.setup(LCD_RS, GPIO.OUT) 
GPIO.setup(LCD_D4, GPIO.OUT) 
GPIO.setup(LCD_D5, GPIO.OUT) 
GPIO.setup(LCD_D6, GPIO.OUT) 
GPIO.setup(LCD_D7, GPIO.OUT) 

def convert1(data, i): # signed 16-bit value 
    return c_short((data[i]<< 8) + data[i + 1]).value 

def convert2(data, i): # unsigned 16-bit value 
    return (data[i]<< 8) + data[i+1] 

def readBmp180(addr=deviceAdd):  
    value = bus.read_i2c_block_data(addr, regCall, 22) # Read calibration data 

    # Convert byte data to word values 
    AC1 = convert1(value, 0) 
    AC2 = convert1(value, 2) 
    AC3 = convert1(value, 4) 
    AC4 = convert2(value, 6) 
    AC5 = convert2(value, 8) 
    AC6 = convert2(value, 10) 
    B1 = convert1(value, 12) 
    B2 = convert1(value, 14) 
    MB = convert1(value, 16) 
    MC = convert1(value, 18) 
    MD = convert1(value, 20) 

    # Read temperature 
    bus.write_byte_data(addr, regMean, regTemp) 
    time.sleep(0.005) 
    (msb, lsb) = bus.read_i2c_block_data(addr, regMSB, 2) 
    P2 = (msb << 8) + lsb 

    # Read pressure 
    bus.write_byte_data(addr, regMean, regPres + (sample << 6)) 
    time.sleep(0.05) 
    (msb, lsb, xsb) = bus.read_i2c_block_data(addr, regMSB, 3) 
    P1 = ((msb << 16) + (lsb << 8) + xsb) >> (8 - sample) 

    # Refine temperature 
    X1 = ((P2 - AC6) * AC5) >> 15 
    X2 = (MC << 11)/(X1 + MD) 
    B5 = X1 + X2 
    temperature = (B5 + 8) >> 4 

    # Refine pressure 
    B6 = B5 - 4000 
    B62 = B6 * B6 >> 12 
    X1 = (B2 * B62) >> 11 
    X2 = AC2 * B6 >> 11 
    X3 = X1 + X2 
    B3 = (((AC1 * 4 + X3) << sample) + 2) >> 2 

    X1 = AC3 * B6 >> 13 
    X2 = (B1 * B62) >> 16 
    X3 = ((X1 + X2) + 2) >> 2 
    B4 = (AC4 * (X3 + 32768)) >> 15 
    B7 = (P1 - B3) * (50000 >> sample) 

    P = (B7 * 2)/B4 

    X1 = (P >> 8) * (P >> 8) 
    X1 = (X1 * 3038) >> 16 
    X2 = (-7357 * P) >> 16 
    pressure = P + ((X1 + X2 + 3791) >> 4) 

    return (str(pressure/100.0)) 

def readDHT(): 
    humi, temp = Adafruit_DHT.read_retry(Adafruit_DHT.DHT11, DHTpin) 
    return (str(int(humi)), str(int(temp))) 

def lcd_init(): 
    lcdcmd(0x33) 
    lcdcmd(0x32) 
    lcdcmd(0x06) 
    lcdcmd(0x0C) 
    lcdcmd(0x28) 
    lcdcmd(0x01) 
    time.sleep(0.0005) 

def lcdcmd(ch): 
    GPIO.output(RS, 0) 
    GPIO.output(D4, 0) 
    GPIO.output(D5, 0) 
    GPIO.output(D6, 0) 
    GPIO.output(D7, 0) 
    if ch&0x10==0x10: 
    GPIO.output(D4, 1) 
    if ch&0x20==0x20: 
    GPIO.output(D5, 1) 
    if ch&0x40==0x40: 
    GPIO.output(D6, 1) 
    if ch&0x80==0x80: 
    GPIO.output(D7, 1) 
    GPIO.output(EN, 1) 
    time.sleep(0.0005) 
    GPIO.output(EN, 0) 

    # Low bits 
    GPIO.output(D4, 0) 
    GPIO.output(D5, 0) 
    GPIO.output(D6, 0) 
    GPIO.output(D7, 0) 
    if ch&0x01==0x01: 
    GPIO.output(LCD_D4, 1) 
    if ch&0x02==0x02: 
    GPIO.output(LCD_D5, 1) 
    if ch&0x04==0x04: 
    GPIO.output(LCD_D6, 1) 
    if ch&0x08==0x08: 
    GPIO.output(LCD_D7, 1) 
    GPIO.output(EN, 1) 
    time.sleep(0.0005) 
    GPIO.output(EN, 0) 

def lcddata(ch): 
    GPIO.output(RS, 1) 
    GPIO.output(D4, 0) 
    GPIO.output(D5, 0) 
    GPIO.output(D6, 0) 
    GPIO.output(D7, 0) 
    if ch&0x10==0x10: 
    GPIO.output(D4, 1) 
    if ch&0x20==0x20: 
    GPIO.output(D5, 1) 
    if ch&0x40==0x40: 
    GPIO.output(D6, 1) 
    if ch&0x80==0x80: 
    GPIO.output(D7, 1) 
    GPIO.output(EN, 1) 
    time.sleep(0.0005) 
    GPIO.output(EN, 0) 

    # Low bits 
    GPIO.output(D4, 0) 
    GPIO.output(D5, 0) 
    GPIO.output(D6, 0) 
    GPIO.output(D7, 0) 
    if ch&0x01==0x01: 
    GPIO.output(LCD_D4, 1) 
    if ch&0x02==0x02: 
    GPIO.output(LCD_D5, 1) 
    if ch&0x04==0x04: 
    GPIO.output(LCD_D6, 1) 
    if ch&0x08==0x08: 
    GPIO.output(LCD_D7, 1) 
    GPIO.output(EN, 1) 
    time.sleep(0.0005) 
    GPIO.output(EN, 0) 

def lcdstring(Str): 
    l=0; 
    l=len(Str) 
    for i in range(l): 
    lcddata(ord(message[i])) 

lcd_init() 
lcdcmd(0x01) 
lcdstring("Circuit Digest") 
lcdcmd(0xc0) 
lcdstring("Welcomes you") 
time.sleep(3) # 3 second delay 

# main() function 
def main(): 

    print 'System Ready...' 
    URL = 'https://api.thingspeak.com/update?api_key=%s' % key 
    print "Wait...." 
    while True: 
      (humi, temp)= readDHT() 
      (pressure) =readBmp180() 

      lcdcmd(0x01) 
      lcdstring("Humi#Temp#P(hPa)") 
      lcdstring(humi+'%'+" %sC %s" %(temp, pressure)) 
      finalURL = URL +"&field1=%s&field2=%s"%(humi, temp)+"&field3=%s" %(pressure) 
      print finalURL 
      s=urllib2.urlopen(finalURL); 
      print humi+ " " + temp + " " + pressure 
      s.close() 
      time.sleep(10) 



if __name__=="__main__": 
    main() 

Answer 1

だから私はコピーして、あなたのコードを貼り付け、余分ながありますラインの前にスペースがあります。

def lcddata(ch): 

とライン203

lcdcmd(0x01) 

と、このすべてのコードがそれに余分なタブがあり、それはないはず

def main(): 

print 'System Ready...' 
URL = 'https://api.thingspeak.com/update?api_key=%s' % key 
print "Wait...." 
while True: 
     (humi, temp)= readDHT() 
     (pressure) =readBmp180() 

     lcdcmd(0x01) 
     lcdstring("Humi#Temp#P(hPa)") 
     lcdstring(humi+'%'+" %sC %s" %(temp, pressure)) 
     finalURL = URL +"&field1=%s&field2=%s"%(humi, temp)+"&field3=%s" %(pressure) 
     print finalURL 
     s=urllib2.urlopen(finalURL); 
     print humi+ " " + temp + " " + pressure 
     s.close() 
     time.sleep(10)